# Promise Robotics

Runs local robotic factories that make wall, floor, stair and roof framing for home builders, sold as factory output, not plants.

- **Operating status:** Active. Venture-backed. Signed D.R. Horton for more than 1,250 Phoenix homes in October 2026 and raised a C$40 million Series B in November 2026; a Phoenix plant is due in early 2027. [4][7]
- **Momentum:** Expanding
- **Ownership:** Independent
- **Headquarters:** Toronto, Ontario, Canada
- **Founded:** 2021
- **Role:** Manufacturer, Supplier, Software
- **Method:** Panels
- **Product:** Panels, Components
- **Builds:** Single-family, Multifamily
- **Website:** https://www.promiserobotics.com/ (loaded when checked)

Checked 2026-11-20. Page: https://nowcitylabs.com/fieldguide/construction/p/promise-robotics/

## Summary by the Lead Analyst

Promise Robotics owns and runs robotic factories that make framing for home builders, who buy the output instead of building plants. It runs plants in Calgary and the Edmonton area and plans a 16,000 sq ft Phoenix plant for D.R. Horton in 2027. BetaKit reported over 200 builds done, 2,500 homes under contract and 80 staff in October 2026. It raised $15 million in 2023 and C$40 million in 2026. Not public: homes per plant per year, prices and any measured waste or carbon data.

Verify first: Confirm the Phoenix plant opens on time for the D.R. Horton homes and what share of each home the factory frames.

## What it is

Promise Robotics was founded in 2021 and is based in Toronto. Ramtin Attar, a former Autodesk leader, is co-founder and chief executive; Reza Nasseri, a Canadian home builder, is co-founder and chief innovation officer. It sells what it calls Factory-as-a-Service: Promise owns the factory, robots and software, its own crews run them, and builders pay for what the factory produces. [6][1][7]
Its software reads a builder's existing plans, makes production plans and robot instructions, and links production to site installation. Off-the-shelf KUKA arms with its own tooling build wall panels with windows and doors, floors, stairs and roofs; installers then assemble them on site. Its sweet spot is three- and four-story townhomes, and it also frames single-family homes, duplexes and fourplexes. [4][6][5]
HousingWire reported that it sends instructions to local factories and aims to build production density in each market. It runs plants in Calgary and the Edmonton area, and its first U.S. plant, 16,000 sq ft in Phoenix, is due to start in early 2027 for a D.R. Horton agreement covering more than 1,250 homes. [5][4][7]

## Key facts

- Founded: 2021 [6]
- Headquarters: Toronto, Ontario [4][6]
- Factory: Calgary (60,000+ sq ft), Edmonton area; Phoenix due 2027 [3][4]
- Homes delivered: Over 200 builds; about 2,500 homes under contract (2026) [4]
- Funding raised: $15 million Series A (2023); C$40 million Series B (2026) [2][7]
- Employees: 85, planning more than 100 (November 2026) [9]

## Production and technology

- Production: Micro-factory, Local factories serving several builders; Phoenix plant 16,000 sq ft [5][4][6]
- Technology: Robotics, Off-the-shelf KUKA arms with its own tooling build framing [6][2]
- Technology: Physical AI, Computer vision and a reasoning model plan and direct the robots [6][2]

## Card fields

The same twelve fields every card, table row and comparison shows. A missing value says why: No data, Not published, N/A or Not yet rated.

- Method: Panels
- Materials: No data
- Products: Panels, Components
- Building markets: Single-family, Multifamily
- Factory: Calgary, AB; Nisku, AB
- Markets served: Alberta, Arizona
- Demonstrated scale: 200 homes delivered, 2026
- Annual capacity: No data
- Cost: No data
- Green: Not yet rated
- Value: Not yet rated
- Evidence: Partial · Checked Nov 2026

## Measured

- Units delivered: 200 homes delivered, 2026 (BetaKit report of more than 200 builds completed, framing only) [4]
- Factory floor area: 60,000 sq ft factory floor area [3]

## Factories

- Calgary, Alberta, Canada: 60,000 sq ft, More than 60,000 sq ft at 11575 Stonehill Drive NE; launched October 2025 [3][4][13]
- Nisku, Alberta, Canada: Edmonton area plant; BetaKit names it Edmonton [7][4]

## Serves

- Alberta (CA-AB) [3][7]
- Arizona (US-AZ) [4]

## Timeline

- 2021 (founded): Founded, according to The Robot Report. [6]
- 2023-11-02 (funding): Raised a $15 million Series A led by Horizons Ventures, bringing total funding to $25 million; Goodmans reported the round as C$20.8 million. [2][8]
- 2024-05-13 (funding): Signed a National Research Council IRAP contribution agreement, An AI-Enabled Robotic Solution for Building Component Prefabrication, running to March 31, 2025. [10]
- 2025-06-16 (funding): Signed a second NRC IRAP contribution agreement, Advancing Autonomous Systems for Scalable Robotic Prefabricated Panel Production, running to March 31, 2026. [11]
- 2025-06-24 (funding): PrairiesCan announced a $2.5 million contribution to establish a robotics-driven homebuilding factory; the federal grant record names Calgary. [12][13]
- 2025-10 (factory): Set up its flagship robotic factory in Calgary with more than 60,000 sq ft, Built In reported. [3]
- 2026-10-13 (milestone): Signed a multi-year agreement with D.R. Horton for more than 1,250 homes in the Phoenix area, its first U.S. customer, and announced a 16,000 sq ft Phoenix plant due in early 2027. [4][6]
- 2026-11-17 (funding): Raised a C$40 million Series B led by White Star Capital. [7][9]

## Findings by five AI specialists

A level is the strength of the public evidence for one specialist, on a scale of 0 to 4. It is not a grade of the company, and there is no total.

### Materials and Circularity: Claims only (level 1)

The Robot Report noted in October 2026 that Phoenix homes needed about 50 percent less sheathing than Canadian ones, a design difference, not a waste figure. No offcut rate, material yield or recycling data from its plants was found as of November 2026.

- Evidence: The Robot Report reported that Phoenix required about 50 percent less sheathing and different bracing than Canada. [6]
- Gap: Measured lumber and sheathing waste per home at its plants and where offcuts go.

### Energy and Carbon: Claims only (level 1)

The Robot Report reported in November 2023 a company estimate that every million new homes built its way would cut greenhouse gas emissions by 560 MT, unit as stated. It is a projection without a method or verifier. No energy or embodied carbon figure for homes it framed was found.

- Evidence: The Robot Report reported a company estimate of a 560 MT cut in greenhouse gas emissions per million new homes. [2]
- Gap: Embodied carbon of its framing compared with site framing, with a method and a verifier.

### Cost and Access: Claims only (level 1)

The company site claims savings of $300 per home per day and 60 percent faster construction. No price per home or per panel and no affordable homes delivered are documented as of November 2026.

- Evidence: The company site claims savings of $300 per home per day and 60 percent faster home construction. [1]
- Gap: What builders pay per home framed and whether savings reach buyers.

### Workforce: Third-party evidence (level 3)

BetaKit reported 80 employees in October 2026 and, citing The Globe and Mail, 85 in November 2026 with plans for more than 100. The United Brotherhood of Carpenters invested in 2023, and its own crews run its systems. No wage, training or safety data is public.

- Evidence: BetaKit reported 80 employees in October 2026 and, citing The Globe and Mail, a plan to grow from 85 to more than 100 in November 2026. [4][9]
- Evidence: The Robot Report listed the United Brotherhood of Carpenters among Series A investors in November 2023. [2]
- Evidence: The Robot Report reported in October 2026 that Promise's own crews operate the systems. [6]
- Gap: Workers per plant, wages, training programs and safety records.

### Delivery Record: Third-party evidence (level 3)

BetaKit reported over 200 builds completed for builders including Brookfield, Hopewell and Mattamy, and about 2,500 homes under contract, in October 2026. Press confirms $15 million raised in 2023 and C$40 million in 2026. No yearly output by plant is published.

- Evidence: BetaKit reported over 200 builds completed and just over 2,500 homes under contract. [4]
- Evidence: The Robot Report reported a $15 million Series A in November 2023, bringing total funding to $25 million. [2]
- Evidence: The Next Web reported a C$40 million Series B led by White Star Capital in November 2026. [7]
- Gap: Homes framed per plant per year and confirmation that the Phoenix plant opened.

## Sources

1. [Promise Robotics home page](https://www.promiserobotics.com/) (Promise Robotics)
2. [Promise Robotics brings in $15M to bring automation to homebuilding](https://www.therobotreport.com/promise-robotics-brings-in-15m-to-bring-automation-to-homebuilding/) (The Robot Report)
3. [Promise Robotics Launches Homebuilding Facility in Calgary](https://builtin.com/articles/promise-robotics-calgary-facility-20251015) (Built In)
4. [Promise Robotics strikes deal to supply largest US homebuilder DR Horton](https://betakit.com/promise-robotics-strikes-deal-to-supply-largest-us-homebuilder-dr-horton/) (BetaKit)
5. [D.R. Horton tests Promise Robotics factory model for 1,250 homes](https://www.housingwire.com/articles/promise-robotics-dr-horton-factory/) (HousingWire (The Builder's Daily))
6. [Promise Robotics partners with D.R. Horton on physical AI for homebuilding](https://www.therobotreport.com/promise-robotics-partners-d-r-horton-physical-ai-homebuilding/) (The Robot Report)
7. [Promise Robotics raises C$40M for robot factories that build homes](https://thenextweb.com/news/promise-robotics-40m-cad-series-b-robot-homebuilding) (The Next Web)
8. [Proptech Startup Promise Robotics Completes $20.8M Series A Financing](https://www.goodmans.ca/insights/post/goodmans-tech-blog/proptech-startup-promise-robotics-completes-20.8m-series-a-financing) (Goodmans LLP)
9. [Physical AI company Promise Robotics announces $40-million Series B round](https://betakit.com/physical-ai-company-promise-robotics-announces-40-million-series-b-round/) (BetaKit)
10. [Grants and Contributions: An AI-Enabled Robotic Solution for Building Component Prefabrication (agreement 1019061)](https://search.open.canada.ca/grants/record/nrc-cnrc%2C172-2024-2025-Q1-1019061%2Ccurrent) (Government of Canada, Open Government)
11. [Grants and Contributions: Advancing Autonomous Systems for Scalable Robotic Prefabricated Panel Production (agreement 1032073)](https://search.open.canada.ca/grants/record/nrc-cnrc%2C172-2025-2026-Q2-1032073%2Ccurrent) (Government of Canada, Open Government)
12. [Minister Olszewski announces support to help Alberta businesses diversify, scale up and thrive](https://www.canada.ca/en/prairies-economic-development/news/2025/06/minister-olszewski-announces-support-to-help-alberta-businesses-diversify-scale-up-and-thrive.html) (Prairies Economic Development Canada)
13. [Grants and Contributions: Establish a robotic home manufacturing facility in Calgary (PC0009978)](https://search.open.canada.ca/grants/record/prairiescan%2CGC-WD-DEO-2024-2025-Q4-68%2Ccurrent) (Government of Canada, Open Government)
